Craft day!

Now that all the sewing is done, I am making a different kind of mess!  A crafty mess.  I've been working on the broach for Sailor V/ Sailor Venus, the shoulder wing armor for Sailor V and V's Crescent Compact.


The broach is currently gluing.  I tried just attaching the worbla to the back of it, but that just popped apart. Which makes sense, but I was not entirely awake yet when I started that, so didn't think about it at the time.  The back which has the pin attachment (not pictured) is still worbla, but is being glued to the Gemstone (paperweight) with weld-bond glue.  It seems to be working, but needs pressure to fully work right (hense the clamps).

I cut out and shaped the sleeve wing/armor things today. They are also made from worbla, cause I had some lying around still. Molding worbla onto the body is (go figure) 10times harder when it is just you doing it, so sadly I have more air bubbles then I would have liked. I am hoping I can hide those with the gesso layers though.

 The Crescent compact is coming along well! I'm pretty proud of it so far.  the top is 2 layers of Craft foam glued together, with the crescent that goes around the red gem molded in, and the bottom is 3 layers of foam. I wanted it to have a bit of depth to it and not just be 2 flat single layers of craft foam on both sides, covered in Worbla.

The compact will click closed with magnets when done, be spray painted gold and have gems on top.  The hardest part with this prop was trying to figure out how to hinge it so I could open and close it.  Logically, one would think the hinge would be on the rounded edge, but logic has forsaken this compact and the hinges as you can see are on the points of the crescent.

So, after a lot of thinking and asking for advice, suggestions included drilling a hole and attaching them with a wire loop, which would work, but would probably not stand up on its own, adding in springs, more magnets or a hinge.  I went with a hinge.  I looped some very small worbla noodles tightly over some cut off q-tips, this gave me a nice tight, rounded fit like the plastic hinges on many toys.  I allowed it to cool down till it was cold/hard again before gently turning the q-tip to get it out again. This left me with perfect little loop hinges that work great! I just need to cut down the last bit of my q-tip and add some sort of stopper (probably a bead of worbla or plastic) so the hinge dosn't come out.

The effect is pretty good so far, though I may switch out the Q-tips I have for something else, as mine appear to be compressed paper and that does not bode well in case of rain or accidental wetting.

 Now begins the boring (and messy) stage of layer upon layer of gesso, then sanding, then a couple more layers of gesso, then more sanding etc etc till I have a smooth surface to paint.

Sailor V is almost done!

The shirt and skirt are done.  Today I am working on the broach, Shoulder armor and her compact prop.

I'll be making this baby out of craft foam and worbla.

Easy-peasy Sailor Collar stripes.

Sailor collars, they all have stripes and there are so many ways to attach them.

You can sew them down by hand or by machine.   I sewed the Soutache braid stripes on this collar by machine. If it is wobbly it is because this is one of my first cosplays from 2005.

The stripes on my  Escaflowne movie Hitomi cosplay (one of my first!) sewn down by machine.

You can glue them down, which works great with vinyl! just make sure to clean up your edges and don't use too much, (I used too much here because this was maybe my second or third ever cosplay!)  Glue
can be messy and sometimes hard to get off, plus over time the glue may dry over time and start to peel away, but if that happens, just re-glue it.

The details on my PGSM Dark Merucry collar, done with glue. (Probably my 3rd cosplay ever)

Over time I found that best product to attach the trim is Steam-a-Seam or Heat-n-Bond.  I prefer Steam a Seam, but both would work. Both can be found at fabric stores or online. Heatn' Bond is sold by the meter and Steam-a-Seam is by the meter, in sheets and in rolls.  I used to cut the strips to size for my ribbon details from the sheets or from a meter, but I found thought I'd try this beauty this time:

It's already pre-cut into strips and comes on a roll like tape! My life just got easier!  I just used it to put down the red stripe on my Sailor V costume. My ribbon was wide enough that I had to run two strips of the steam-a-seam side by side. I did each edge separately and cut the steam-a-seam off at the corners, but I did not cut my ribbon! That stayed in one big strip off my spool until I had done all 3 edges. The last thing I wanted was to accidentally cut it too short.

The steam-a-seam is sticky like a post-it-note, so until you iron it down it can be moved around, but it also means the ribbon sometimes comes un-tacked, so I did it one edge at a time. When I got to the corner, I did a mitered corner. Which is a fancy way of saying that I sewed it on an angle so I'd have a pretty corner.

This is what that mitered edge looks like when it is done. I then proceeded to run the ribbon along the bottom edge till I got to the next corner and mitered the other corner.  Once everything was tacked down I cut the ribbon off the spool.

Finally I ironed my ribbon down, and here is the finished product!

Sailor V top mock up!

I mocked-up my Sailor V shirt today!  Over all it turned out pretty good. I will be taking the collar in 1-2 cm along the back, I find it too big.  And I think i will be shifting the sleeve (not pictured) so the split between the red and white will be more even.

The front looks good. I *may* widen the collar opening (not 100% sure yet) and I think I may need to take it in a bit.

In the name of the Moon!

Because Sailor V does say that before Sailor Moon.  Yesterday, I started drafting the patterns for Sailor V from the Sailor V Manga and later the Sailor Moon Manga. V is one of 3 costumes I am making for myself to wear to Anime North 2016.  The other two are of course Sailor Venus and Princess Venus.  I've even got a white cat lined up to borrow for photos!

Behold! The early 90's glory of her costume!

The makings of a Magical Girl.

 Ah, pattern drafting.  The pattern math is like school, the cutting like art class and the mess left on my hands from all that graphite dust, and eraser shavings collateral damage.

Seriously, it looks like it snowed on my cutting surface.

 I'm going to mock up the top tomorrow.  It's a simple crop top, but I want to make sure it is long enough for my torso and that the collar looks the way I want it to before I sew the actual thing.

Top parts.

I finished the patterns today. I think this is one of the fastest costumes I have ever drafted and one of the smallest.

YAY!

RWBY Neo costume

I also got back the photos from the amazing and awesome HM Cosplay Photograpy of my Neo costume.  She does amazing work, you should go check her out on Facebook!

SEVEN: Pride

SEVEN came down on the 19th, so now I think I am free to post pictures of the final thing!
PRIDE
Designer:me

Model:me!
Make-up: Billy Peterson
Photography: Lance Kenneth Blakney